On Q Legrand Switch IS 0320 REV O User Manual

INSTRUCTION/INSTALLATION SHEET  
SINGLE SOURCE 4 ZONE AUDIO  
DISTRIBUTION HUB  
301 Fulling Mill Road, Suite G  
Middletown, PA 17057  
Phone (800) 321-2343 / Fax (717) 702-2546  
IS-0320 REV. O  
1. Introduction  
The On-Q /Legrand Single Source 4 Zone Audio Distribution  
Hub, PN F7396 (see Figure 1), is an integral part of the  
Category 5 Audio System. It is a component which, when  
combined with other essential components and your source  
equipment receiver, CD player, etc, creates a versatile whole-  
house audio system that will fill your rooms with high-quality  
sound for years to come. Category 5 technology is a new,  
innovative method of providing high quality audio to remote  
locations with a single 8-conductor cable such as Category 5.  
This technology provides many advantages over other  
conventional methods of audio distribution such as simple,  
single Category 5 wiring scheme, and infrared control of  
system components.  
Figure 1  
2. Description  
All components of the Category 5 Audio System are wired centrally from the Category 5 Audio Distribution Hub  
located within the structured wiring enclosure. In addition to providing a central point of connection, the Hub  
distributes the necessary voltage to power the system. The Single Source Input and Volume Controls connect  
directly to the module utilizing RJ-45 connections. The system can support multiple modules through “daisy  
chaining” the Audio Distribution Hubs.  
NOTE: The 24 volt, 2.5 amp Power Supply, PN F7723, is not included and must be purchased separately.  
3. Installation  
Installation of the On-Q/Legrand Audio Distribution Hub and related components, is best accomplished at  
multiple times during new construction, at “Rough-in” before the drywall is installed, and at “Trim-out” after the  
drywall is installed and painted.  
IMPORTANT: Read the manuals that are included with all associated Category 5 Audio products before  
installation of any single component! If you are unsure of any of the following installation procedures  
contact On-Q/Legrand Technical Support @ 1-800-321-2343 option 1 or contact an On-Q/Legrand  
installer.  
NOTE: The Category 5 Audio Distribution Hub provides power to all of the components of the Category 5  
Audio System.  
NOTE: To provide ultimate flexibility for future products, run two Category 5 cables from the Single  
Source Input to the Single Source 4 Zone Distribution Hub. Also, run a 16/2 or 16/4 speaker cable, along  
with the Category 5 cable, from the Single Source 4 Zone Distribution Hub to each volume control  
location.  
Page 1 of 3  
©Copyright 2005 by On-Q/Legrand All Rights Reserved.  
 
INSTRUCTION/INSTALLATION SHEET  
SINGLE SOURCE 4 ZONE AUDIO  
DISTRIBUTION HUB  
301 Fulling Mill Road, Suite G  
Middletown, PA 17057  
Phone (800) 321-2343 / Fax (717) 702-2546  
IS-0320 REV. O  
4. Important Safety Precautions:  
READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING THE CATEGORY 5 AUDIO SYSTEM.  
• Do not attempt to service, move or change any component of this system unless you are qualified to do so.  
This system should be installed by a qualified installer and must conform to all local building and electrical codes.  
• Do not apply power to the Category 5 Audio System until all components have been installed and all wiring has been  
properly terminated.  
• Do not attempt to terminate, change or un-install any wiring without first turning off power at the Category 5 Audio System  
which is located in the enclosure. Unplug the power transformer that is powering the Category 5 Audio System from the  
power outlet before proceeding with wiring terminations or changes.  
Install each component of this system away from heat sources such as HVAC ducts/registers, stoves or any other heat  
source.  
• Do not expose any component that was designed for indoor use to moisture. Doing so can create electrical hazards or  
render the component unusable. Exposure to moisture will also void the warranty on the system.  
Only use a damp cloth to clean the cover plates of the system components. Do not use vacuum cleaners, liquid or aerosol  
cleaners.  
Page 3 of 3  
©Copyright 2005 by On-Q/Legrand All Rights Reserved.  
 

Miele Washer Premier 520 User Manual
Miele Washer w 3204 User Manual
Miller Electric Welder AA40GBU User Manual
Milwaukee Impact Driver 2452 20 User Manual
Minolta Digital Camera ME 0308 User Manual
Moxa Technologies Surge Protector A51 User Manual
NEC Calculator NDA 30103 004 User Manual
Nilfisk ALTO Vacuum Cleaner ATTIX 965 0H M SD XC User Manual
Output Solutions Printer C I 8 0 6 0 User Manual
Paradigm Speaker 100 User Manual