Operating Instructions
Vented dryer
T 7634
To avoid the risk of personal injury or
damage to the appliance, it is
essential that you read these
operating instructions before
installation and use. This maschine
is not approved for use in the
United States.
en - CA
M.-Nr. 07 323 240
Contents
Caring for the environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Operating the dryer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Laundry care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Care symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Drying tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Proper drying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Brief instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Options/Delay. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Gentle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Buzzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Program Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Changing the program sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Switching over from a running program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
- Canceling and selecting a new program . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
- Interrupting a program and removing laundry . . . . . . . . . . . . . . . . . . . . . . . . 19
Loading or removing laundry. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Time remaining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Electronic lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Cleaning door lint filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Cleaning port-hole grilles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Cleaning the dryer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Trouble shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
What to do, if . . . ? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Test and fault messages.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Other faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Replacing the light bulb. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Customer service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Repairs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Program updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Warranty conditions and warranty period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Optional accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
3
Contents
Installation and connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Front view. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Rear view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Installation site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Carrying the dryer to the installation site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Washer-dryer stack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Leveling the dryer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Ventilating the installation area. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Electrical connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Installing the dryer vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Calculating total duct length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Rear or side exhaust connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
aFlexible metal duct hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
bDryer vent systems from metal piping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
cConnecting directly to a wall vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
dVent collector duct . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Washer-dryer stack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Programmable functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Extending the range of drying levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Adjusting buzzer volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Set memory function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Extending cooldown time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Change function of Filter/Vent indication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Adjust keypad tone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Changing water conductivity setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
4
IMPORTANT SAFETY INSTRUCTIONS
Before this appliance is removed for
~
,This machine T 7634 meets all
service or discarded, remove the door
to the drying compartment.
CSA requirements. This machine is
not approved for use in the United
States.
Do not reach into the dryer if the
~
drum is moving.
Do not install or store this appliance
~
where it will be exposed to the weather.
,WARNING - To reduce the risk of
fire, electric shock, or injury to
persons when using your appliance,
follow basic precautions, including
the following:
Do not tamper with the controls.
~
Do not repair or replace any part of
~
the appliance or attempt any servicing
unless specifically recommended in
these operating instructions. Repairs to
electrical appliances should only be
performed by qualified personnel.
Incorrectly repaired machines may
pose a considerable risk to the user.
It is essential to read all instructions
~
before using the appliance.
Do not use fabric softener sheets to
~
eliminate static in this dryer. Best
results are achieved when a liquid
softener is used in the washer. Follow
the manufacturers instructions.
The dryer is designed for household
~
use only and only for drying textiles that
have been washed in water and whose
fabric care label states that they can be
tumble dried. Other uses may be
dangerous. Miele will not be held liable
for damage caused by improper use or
incorrect operation.
To prevent the risk of fire, the
~
following textiles must not be dried in
this dryer:
– items which have not been washed.
– items, such as work-wear, exposed
to grease, oils, or other deposits
(such as lotions or cosmetics) in your
dryer. If these items have not been
thoroughly cleaned there is a danger
that they may contribute to a
Do not allow children to play on or in
~
the appliance. Close supervision is
necessary when the appliance is used
near children. Always close the door
after use to prevent child hazards.
This appliance is not intended for
chemical reaction that could cause
the laundry to ignite when heated
even after being removed from the
dryer.
~
use by persons (including children)
with reduced physical, sensory or
mental capabilities, or lack of
experience or knowledge, unless they
are supervised whilst using it or have
been shown how to use it by a person
responsible for their safety.
5
IMPORTANT SAFETY INSTRUCTIONS
– items that have been previously
cleaned, washed, soaked or spotted
with gasoline, dry-cleaning solvents
or other flammable or explosive
substances. They may give off
Keep the area around the air intake
~
(toe kick) and adjacent surrounding
areas free from lint, dust and dirt.
The interior of the machine should
~
be cleaned periodically by qualified
personnel.
vapors that could ignite or explode.
– items treated with flammable
cleaning agents or items containing
acetone, alcohol, gasoline, stain
remover, wax or chemicals from
buffing, etc.
This dryer is intended for
residential use only!
GROUNDING INSTRUCTIONS
~
This appliance must be grounded. In
the event of malfunction or breakdown,
grounding will reduce the risk of
– items which have been splashed with
hair spray, nail polish remover, etc.
electric shock by providing a path of
least resistance for electric current.
This appliance is equipped with a cord
having an equipment grounding
When washing heavily soiled items
ensure that sufficient detergent is
used with a high temperature. If in
doubt wash the item several times.
conductor and a grounding plug. The
plug must be plugged into an
– items containing foam rubber or
similarly textured rubber-like
materials.
appropriate outlet that is properly
installed and grounded in accordance
with all local codes and ordinances.
– items with padding or filling (e.g.
pillows or jackets) which have been
damaged. Loose filling could catch
fire.
WARNING – Improper connection of
~
the equipment-grounding conductor
can result in a risk of electric shock.
Contact a qualified electrician if you are
in doubt as to whether the appliance is
properly grounded.
WARNING – Never stop a tumble
~
dryer before the end of the drying cycle
unless all items are quickly removed
and spread out so that the heat is
dissipated.
Do not modify the plug provided
~
with the appliance: if it will not fit the
outlet, have a proper outlet installed by
a qualified electrician.
Allow the dryer to complete each
~
stage of the program selected,
including the cooling down phase. This
will ensure that the items being
removed are not too hot to handle
A faulty power cord must be
~
replaced by a genuine Miele power
cord.
Do not use the dryer without a lint
~
screen or with a damaged lint screen.
Clean the lint filter before or after
~
each load.
Lint screens must be cleaned
~
regularly!
6
IMPORTANT SAFETY INSTRUCTIONS
The dryer should not be operated
~
without a vent duct.
Safe operation and avoidance of an
underpressure of 4 Pa or more should
in any case be confirmed by your
Master Chimney Sweep.
It should not be connected to a
~
chimney used for other purposes.
Keep the room in which the dryer is
~
Do not place the dryer in a room
~
installed free of dust and fluff.
Dirt particles in the entering air promote
stoppages.
where there is a risk of frost occurring.
Temperatures around freezing affect
dryer performance.
Acceptable room temperature should
lie between +2°C and +35°C.
Do not support yourself or lean on
~
the door. The dryer might tip over.
Check all components of the venting
Close the door after every drying
~
cycle. In this way you can prevent
~
system (such as the wall pipe, external
grill, elbows and bends, etc.) for
airtightness. Lint can build up,
impeding airflow.
– children from trying to climb into the
dryer or leaving objects inside it.
If a pre-existing system is present, it
should be checked before the dryer is
installed.
– small animals from getting into the
dryer.
Do not hose down the dryer.
~
Ducting must not be connected to a
~
fireplace or gas flue that is in use, nor
to ducting which ventilates rooms with
fireplaces. Otherwise there is the
danger of smoke or exhaust gas being
driven back.
Accessories
Accessory parts may only be
~
attached or installed when they have
been expressly approved by Miele.
If other parts are added or installed,
guarantee, performance and/or product
liability claims are invalidated.
A suffocation and poisoning
~
hazard exists from suction of exhaust
gases, when gas water heaters, space
heaters, coal stoves with chimney
connections, etc., are installed in the
same room, or in the dwelling, or in
neighboring rooms and the under
pressure is 4 Pa or more.
The manufacturer will not be held
liable for damage caused by failure
to comply with the safety instructions
and warnings.
Prevent underpressure by sufficient
room ventilation, by, for instance:
– unclosable ventilation openings in
the external wall, or
SAVE THESE INSTRUCTIONS
– a window switch:
the dryer can only be switched on
with the window open.
7
Operating the dryer
Control panel
aDisplay
fGentle button
bDelay button
Delicate fabrics are dried at a lower
temperature.
This button has a dual function:
- Selecting the duration of the
Timed cold and Timed warm
programs.
gDryness button
Indicator lights identify the drying
level selected.
- Pre-selection of start time.
hProgram selector
cBuzzer button
Indicator lights identify the program
selected.
The end of the program is signaled
audibly.
iDoor button
dFault indicator / Optical interface
This button opens the door
Description: See "Problem solving /
Customer service" section.
independently of the power supply.
jI-On/0-Off button
eStart/Stop button
For switching the dryer on and off.
Starts and stops a program.
Interrupts a program when pressed.
Flashes during program selection
and lights once the program starts.
8
Operating the dryer
Display
In this way, the delicate and smoothing
programs can end earlier, when a
certain temperature is reached. This
can happen with particularly fine
fabrics, very small loads, or if items
have previously been dried.
The following functions are selected
from the display:
– Delay
– Selecting duration of timed
programs.
Delay
– Programmable functions.
The display also shows:
– Program duration.
The delay time selected will be
displayed.
The delay time countdown begins after
pressing the Start button.
– Program stage:
Drying
Once the time delay expired, the
Cooling down
End.
estimated program duration will appear
in the display and the drying begins.
– Test and fault messages.
Programmable functions
Program duration/ Estimated time
remaining
The programmable functions can be
used to adapt the dryer to your
personal requirements. In programming
mode, the display will show the function
selected.
When a program is selected, the
estimated time remaining will be
displayed. This is to be considered an
estimate only.
The following factors can lead to
variations in the time remaining
estimate: Residual moisture after
spinning; type of fabric; size of load;
ambient temperature, or fluctuations in
the power supply.
The adaptive electronics constantly
adjusts to the individual wash load to
ensure a more accurate estimate of
time remaining. This estimate is
permanently monitored during drying,
which in some cases can lead to a
change in the estimate.
9
Laundry care
Care symbols
– Do not dry fabrics that are still
soaking wet! After washing, spin
fabrics for at least 30 seconds.
Drying
q
r
Normal/higher temperature
– Dry mixed loads of cottons, colors
and easy-care fabrics in the in the
Express program.
reduced temperature: select
Gentle
(for delicate fabrics)
– Open jackets so that they dry evenly.
s
Not suitable for dryer
– Woolens and wool blends tend to
mat and shrink. Only handle these
fabrics in the Woolens program.
Ironing and rotary ironing
I
H
G
J
very hot
hot
– The linings of down-filled garments,
depending on quality, tend to shrink.
Handle these fabrics only in the
Smoothing program.
not very hot
Do not iron/rotary iron
Drying tips
– Pure linens are dried only when
indicated on the care label.
– Always check the weight
recommendation for maximum loads
as listed in the "Program Overview"
section.
Otherwise the fabric may become
rough. Handle these fabrics only in
the Smoothing program.
– Cottons (such as T-shirts and
underwear) depending on quality,
often shrink at the first wash.
Overloading will cause wear and
tear on the laundry, give a poor
drying result and cause more
creasing.
Therefore: to avoid further shrinkage,
do not over-dry these textiles.
– Starched laundry may be dried. To
achieve the usual finish, however,
use a double amount of starch.
– Wash new colored fabrics separately
before the first drying. Do not dry
them together with light-colored
fabrics since their colors may run
and discolor other garments or even
plastic dryer components.
10
Laundry care
– Wrinkling increases with larger loads.
This especially occurs with very fine
fabrics as used in shirts and blouses.
To limit wrinkling the dryer performs the
following actions:
1. Tumble drying with drum reversal
(prevents roll-ups of laundry,
creasing and uneven drying),
2. Constantly measures the
temperature of air coming into and
leaving the drum,
3. Cycles two heater sections for 0, half
and full power,
4. Automatic drying stage termination,
after the desired Dryness level of
laundry is reached. To do this, the
dryer is equipped with systems:
- water conductivity metering,
- sensing of laundry’s residual
moisture,
- software.
5. Cooling down with tumbling and
drum reversal,
6. Anti-crease with drum reversal.
In cases of doubt, reduce the load by
dividing it.
Use the Dress shirts program.
11
Proper drying
Brief instructions
Do not exceed maximum loads
specified in the "Program Overview"
Section.
The operating steps identified with
numbers(A, B, C, ...) may be used as
short-cut instructions.
Overloading may cause wear and
tear on the laundry and adversely
affects drying.
A Preparing the laundry
Loosen the washed garments and sort
them by: . .
^ Before closing the door, check that
the lint filter is properly inserted in the
door casing.
. . . desired drying level,
. . . type of fabric and finish,
. . . size,
. . . same residual moisture content
after spinning.
This will produce very even drying.
,Remove foreign objects like
detergent dispensing devices from
the laundry. They can melt and
damage the dryer and the wash.
– Check hems and seams to ensure
that linings don't come out.
– Close duvet covers and pillowcases
to prevent small items from getting
inside.
Ensure that no small items are
jammed in the door, because they
might otherwise be damaged.
– Fasten hooks and close buttons.
– Tie fabric belts together.
B Turn on the dryer
You may also switch the dryer on after
loading it, as the drum will not be
illuminated, to save energy.
^ To turn it on, press the I-On/0-Off
button.
C Loading the dryer
^ Press the Door button to open.
^ Place the laundry loosely in the drum.
12
Proper drying
D Select program
Woolens and Smoothing programs:
– cannot be altered.
Timed program
The Delay button flashes when Timed
cold or Timed warm programs are
selected.
^ Repeatedly press the Delay button
until the required duration appears in
the display.
^ Select the desired program.
Drying time can be selected in
10-minute increments from 20 minutes
up to 2 hours.
The indicator light for the program
selected lights up.
Other indicator lights for drying levels
or extras may be lit, and drying times
displayed.
E Extra options/Select Delay
^ Press button to select the following
options:
Dryness level selection in programs:
Gentle, Buzzer, Delay options (see
"Options/Delay").
– Normal, Wrinkle-free, Express, Dress
Anti-Crease action always activates
at program's end (see next page).
shirts, denim/jeans
Please note: Delay is not possible in
combination with the Timed warm and
Timed cold programs.
^ Press the button repeatedly until the
desired indicator light is lit.
For Normal any dryness level can be
selected, but selection is limited in
other programs.
Note: The estimate of time remaining
shown in the display varies with each
new program selection.
13
Proper drying
F Starting the program
G End of program - Remove laundry
The Start/Stop button flashes during
program selection. This means that a
program can be started.
0 and End appear in the display to
indicate the program end. The buzzer
sounds at intervals (when selected).
^ Press the Start/Stop button.
After the program end the drum rotates
reversible in intervals if clothes are not
removed (Anti-crease action). This
helps to prevent creasing for up to 2
hours.
The Start/Stop button lights.
Drying appears in the display and the
time remaining is counted down.
Before the end of a program
^ Press the Door button.
^ Open the door.
After the drying phase finished a
cooldown phase follows.
^ Remove the laundry.
The following programs have no
cooldown phase: Woolens, Smoothing.
Check that the drum is empty.
Laundry left behind may be
damaged if dried again.
To save energy, the drum light turns off
after a few minutes when the dryer is
not operating and the door is open.
^ To shut it off, press the On/Off button.
^ Clean the lint filter.
^ Close the door.
14
Options/Delay
Gentle
Starting
Delicate fabrics (with the rsymbol on
the care label, such as acrylics) must
be dried at lower temperatures for
longer durations.
^ Press the Start/Stop button.
– The Delay indicator light comes on.
The Delay counts down to program
start as follows:
On some programs Gentle is
permanently set and cannot be
deselected.
– More than I0^, in whole hours.
– Less than I0^, in minutes.
The drum will turn briefly every hour to
prevent creasing.
Buzzer
At the end of the program a buzzer
sounds at intervals, for a maximum of
1 hour.
Canceling / altering Delay
^ Press the Start/Stop button.
The Delay is cancelled.
A continuous warning tone for fault
messages sounds whether the buzzer
is on or off.
^ Repeatedly press the Delay button
until the required duration appears in
the display.
Delay
^ Press the Start/Stop button.
The Delay resumes from the beginning.
Adding laundry
With the Delay option, you can select a
later program start time. Program start
can be delayed by 30 minutes up to a
maximum of 24 hours. This enables
you, for instance, to take advantage of
night electricity rates.
You can add laundry while the Delay is
still counting down:
After program selection:
^ Switch off the dryer.
^ Repeatedly press the Delay button
until the required duration appears in
the display.
^ Open the door and add the laundry.
^ Close the door and switch on the
dryer.
– The Delay indicator light flashes.
– Times of
up to I0^ are selected in 30-minute
steps,
more than I0^ in one-hour steps.
– If you keep the Delay button pressed
in, the time will continue to increase
up to 24^.
15
Program Overview
Normal
Extra dry, Normal
Fabrics
Single- and multi-layered cotton such as: hand towels, T-shirts, baby
clothes.
Note
– Select Extra dry for multi-layered and extra thick fabrics.
– Do not use Extra dry to dry jersey fabrics like T-shirts and baby
clothes - they may shrink.
Gentle
To be selected for delicate fabrics with the care symbol r.
Hand iron, Rotary iron
Fabrics
Cotton or linen fabrics. For example: Table linens, bed linens,
starched laundry.
Note
– You can keep laundry moist if you roll it up until ready to iron it.
To be selected for delicate fabrics with the care symbol r.
Gentle
Wrinkle-free
Extra dry, Normal, Hand iron
Fabrics
Easy-care fabrics in synthetics, cotton or blends. For example:
sweaters, dresses, trousers, skirts, tablecloths.
Note
– To reduce creasing even more, select Hand iron and reduce the
load to 1.5 kg*.
– Fabrics are dried with low creasing with the Hand iron drying
program, depending on fabric type and load.
Gentle
To be selected for delicate fabrics with the care symbol r.
Mixed
Normal, Hand iron
Fabrics
Delicate items made of synthetic fibres, blends or cottons such as
shirts, blouses, lingerie, appliqué fabrics.
Unavailable.
Gentle
16
Program Overview
Woolens
Fabrics
Note
Woolens.
– Remove items immediately after the end of the program while still
slightly damp. Allow items to air dry.
Gentle
Unavailable.
Smoothing
Fabrics
– Cotton or linen fabrics.
– Synthetics, cotton or blends. For example: cotton trousers, jackets,
shirts.
Note
– Program to reduce creases formed during spin cycle in washer.
– Remove garments immediately the program ends and air-dry
Unavailable.
Gentle
Express
Normal, Hand iron
Fabrics
Mixed loads of fabrics for the Normal and Wrinkle-free programs.
Dress shirts
Normal, Hand iron
Fabrics
Gentle
Shirts and blouses.
To be selected for delicate fabrics with the care symbol r.
Denim / Jeans
Normal, Hand iron
Fabrics
Gentle
Denim material like trousers, jackets, skirts or shirts.
To be selected for delicate fabrics with the care symbol r.
17
Program Overview
Timed cold
Fabrics – Any fabric needing airing.
Timed warm
Fabrics – Additional drying of multi-layered garments which dry unevenly
owing to their design: e.g., jackets, pillows and voluminous fabrics.
– Drying individual laundry items: e.g. bath towels, bathing suits, dish
cloths.
Note
Tip:
To start with, do not select the longest time. Determine the most
suitable time by trial.
Use Timed warm to remove or reduce unwanted odors from clean
cotton clothing (duration: 1/2-1 hour). The freshening effect is
reinforced if you moisten the clothing or use a sheet of fabric
conditioner before airing them. Odor reduction will be less for
synthetics.
Gentle
To be selected for delicate fabrics with the care symbol r.
18
Changing the program sequence
Switching over from a running Loading or removing laundry
program
^ Press the Door button.
As a protection against unintentional
^ Open the door.
changes, program selection is no
longer possible.
,Danger of burning:
Do not touch the back of the drum
To be able to choose a new program,
when adding or removing items.
you must cancel the current program.
Temperatures in the drum area can
be high.
- Canceling and selecting a new
program
^ Add or remove laundry as needed.
^ Press the Start/Stop button.
^ Close the door.
The load will be cooled down for a
^ Press the Start/Stop button.
few minutes, until a specific drying
time and temperature have been
Time remaining
reached.
When the program sequence is
changed, the time remaining as shown
by the display may differ from the
actual drying time.
If you press the Start/Stop button
again, the drum stops, End appears
in the display.
^ Switch the dryer off.
^ Then, switch it on again.
^ Select and start a new program im-
mediately.
- Interrupting a program and
removing laundry
^ See below: "Loading or removing
laundry".
^ Turn the dryer off after closing the
door.
19
Electronic lock
C Slowly turn the program selector
step by step through three positions
counterclockwise.
The lock function protects your dryer
against unauthorized use.
The three program indicator lights
must light up in succession.
You can activate this function whenever
you wish.
TheGentle indicator light flashes and
the key symbol 0-§ appears in the
display.
It locks the dryer's electronics. It can be
turned on, but no program can be
started.
E Release the Gentle button.
The lock function has been activated.
^ You may turn off the dryer.
– In such a case, the Gentle indicator
light flashes and a key symbol 0-§
appears in the display.
The door may be opened at any time,
as it is not locked.
Deactivating the lock
Precondition:
Activating the lock
Precondition:
– The dryer is switched off.
– The door is closed.
– The dryer is switched off.
– The door is closed.
^ The procedure is as for "Activating
the Lock". Perform steps A toE.
A Press the Gentle button and keep it
pressed until Step E.
At step E the indicator light for the
Gentle button no longer flashes and the
0-§ key symbol goes out.
B Press the I-On/0-Off button in.
The lock function has been
deactivated.
The Express indicator light comes on.
C Slowly turn the program selector
step by step through three positions
clockwise.
The three program indicator lights
must light up in succession.
20
Cleaning and care
Cleaning door lint filter
The lint screen in the door casing
collects lint generated by the drying
process. Clean it after every drying*.
* Also check the lint screen when
the Filter/Vent indicator light comes
on.
Cleaning the lint screen without
water
Tip: You can dispose of the lint without
touching it by using a vacuum cleaner.
^ Rub or vacuum the lint from the
screen surface.
^ Remove the lint from the space in the
door casing with a bottle brush or the
vacuum.
^ Wipe the door casing seal (2) all
around with a damp cloth.
^ Insert the lint screen fully into the
door casing and close the door.
Cleaning the lint screen with water
The lint screen should be given a
wet cleaning only when it is
severely blocked or plugged.
^ Pull the lint screen (1) out of the door
casing.
^ Clean the lint screen under running
hot water.
^ Dry it thoroughly with care.
21
Cleaning and care
Cleaning port-hole grilles
Cleaning the dryer
Periodically clean the screens in the
door opening as well as the air
passage underneath the screens.
Disconnect the dryer from the
electrical supply.
^ Clean the housing, control panel and
door seal only with a slightly damp
cloth and mild detergent or soapy
water.
^ Clean stainless steel parts (like the
drum) with a suitable stainless steel
cleaner.
Use no scouring products, cleaners
containing solvents, or glass or
all-purpose cleaners. They can
damage plastic surfaces and other
parts.
^ Turn the left and right screen knobs
a (until you hear them click).
^ Dry all parts with a soft cloth.
^ Grasping the knobs, pull the lint
screens out towards the center b.
^ Clean the screens under running hot
water and dry them.
^ Also clean the air passages
underneath the screens, using a
vacuum cleaner, for example.
^ Insert the bottom of the screens and
press the screens upwards.
^ Latch both knobs (until you hear
them click).
22
Trouble shooting
What to do, if . . . ?
You can remedy most problems yourself. In many cases you can save time and
expense, since you will not have to call in customer service.
The following tips should help you locate and remedy the cause of a problem.
Please note the following:
,Repairs to electrical appliances should only be carried out by qualified
professionals. Work performed by unqualified persons can place the user at
considerable risk.
Test and fault messages.
Problem
Cause
Solution
Cancelling a program This is not a fault.
In future, dry individual
laundry items with the
Timed warm program.
0 and End appear in
The electronics recognizes
that there is no laundry in
the display
the drum and cancels the Cancelling test message:
The buzzer sounds.
program.
– Open and close door
Drying of single or already
dried laundry items can
also lead to program
cancellation.
0-§ appears in the
The lock function has been If you wish to dry, you must
display.
activated.
disable the lock function
(see "Electronic lock
function").
Gentle indicator light
flashes.
Cancelling a program The cause is not immedi- – Switch the dryer off and
ately obvious.
then on again.
The buzzer sounds.
– Start a program.
Flashing display may
show Cold air or End.
If program interruption and
error message occur, a
fault is present. Contact
Miele customer service.
23
Trouble shooting
Problem
Cause
Solution
Filter/Vent indicator The indicator light shows
– As a rule, it is sufficient to
clean the lint screens.
Should that not be
light goes on.
that the dryer is not
operating at its most
efficient or economical.
sufficient, then check all
possible causes listed
under "The drying cycle
goes on too long or even
switches off."
Possible causes: Blockage
by lint or detergent
residues.
Cancelling test message:
– Open and close door
The dryer vent duct may be – Pay attention to length
too long, which is not a
dryer fault.
and diameter when
making duct calculation.
See "Installing the vent
duct".
– Too long a vent duct will
result in longer program
times and higher energy
consumption.
You can deactivate the
Filter/Vent indicator lights
(see section on
"Programmable functions").
Cancelling a
program
Possible causes and
remedies are described
above.
Cancelling the fault
message:
Filter/Vent indicator
– Open and close door
– Start a program.
light goes on.
The buzzer sounds.
– If the fault message
comes back, call
Customer Service.
24
Trouble shooting
Other faults
Problem
Cause
Solution
The drying
Please check all possible causes and switch the dryer
process goes on off and then on again.
too long or even
Insufficient ventilation,
Open a door or window and
let in increased air flow.
switches off.
perhaps because the
Even after the lint
installation space is too
screen is cleaned,
small.
the Filter/Vent
The door lint filter is blocked Remove the lint.
with lint.
The vent ducting or its outlet – Check all components of
indicator come
on.
is blocked with lint.
the venting (such as the
wall pipe, external grill,
elbows and bends, etc.)
for unimpeded air flow.
– Remove the lint.
Clothes were insufficiently
spin-dried.
In future, spin textiles in the
washer at a higher rpm.
The dryer is overloaded.
Verify the maximum load for
each drying program.
Metal components such as
zippers have prevented the
moisture level of the laundry
from being determined
accurately.
– In future, open the zippers.
If the problem recurs, in
future dry garments with long
zippers using the Timed
warm program.
The laundry was The load consisted of various – Re-dry with Timed warm.
not satisfactorily fabrics.
– Next time, select a suitable
dried.
program.
25
Trouble shooting
Problem
Cause
Solution
Synthetic-fiber laundry Synthetics have a
Using a fabric softener in
the last rinse cycle can
reduce static charge
when drying.
items are statically
tendency to static
discharges.
charged after drying.
There has been a lint
buildup.
Drying releases fabric lint Lint released is captured
formed primarily from in the door lint filter and
rubbing during wear but can be easily removed
also, in part, from
(see "Care and
Cleaning").
washing. The stress on
fabrics in the dryer is
minimal in relation to their
strength.
26
Trouble shooting
Problem
Cause
Solution
The Dress shirts,
The cause is not imme- – Switch the dryer off and
Denim/Jeans, and Timed diately obvious.
cold programs will not
then on again.
– Select one of the
programs.
start and the indicator
lights for these programs
do not come on.
– If the program will still
not start, there is a fault.
Contact Miele customer
service.
– Meanwhile, use another
program.
The dryer will not start
when switched on.
The cause is not imme- – Is the dryer switched
diately obvious.
on?
– Is it plugged in?
– Is the door closed?
– Check fuses or circuit
breakers.
Drum lighting does not
come on.
The lighting switches off Switch the dryer off and on
automatically to save
energy.
again.
The bulb may need
changing.
You can replace the bulb:
See the end of this section.
27
Trouble shooting
Replacing the light bulb
The bulb should be of the same type
and maximum wattage indicated on
the data plate and the lighting cover.
Disconnect the dryer from the
electrical supply.
^ Open the door.
^ Replace the bulb.
The hinged cover for the lighting is over ^ Fold the cover upwards and press it
the port-hole.
on the right and left until you hear it
latch.
,Ensure that the cover is properly
seated. If moisture gets inside it may
cause a short-circuit.
^ Gently insert an ordinary tool* under
the side of the cover.
* such as a wide slot-type screwdriver
^ Open the cover by pressing lightly
while rotating your wrist.
The cover opens downwards.
The heat-resistant bulb should be
obtained only from Miele customer ser-
vice.
28
Customer service
Repairs
Program updates
For faults you cannot correct yourself,
please contact:
The PC optical interface is used by
Miele customer service to transfer
program updates (PC = Program
Correction) as well as for diagnose and
testing.
– the Miele Factory Repair Service.
The telephone number for the
Factory Repair Service is listed at
the back of these operating
instructions.
In this way, future developments in
fabrics and in the drying procedure can
be integrated into your appliance.
Miele will give timely notification of Pro-
gram updates.
When contacting the Miele Service
Department, you will need to quote the
model and serial number of your
appliance.
Warranty conditions and
warranty period
These can be found on the data plate,
visible when the door is open.
Warranty information can be found in
your warranty booklet.
Optional accessories
Optional accessories for this dryer are
available from Miele customer service.
29
Installation and connection
Front view
aVenting connection: The dryer vent
duct can be connected to the rear of
the machine (as supplied) or on
either the right or left side.
eFour height-adjustable screw feet
bPower cord
cControl panel
dDoor
30
Installation and connection
Rear view
Installation site
This dryer can be accommodated
under a worktop if there is sufficient
height.
,Do not install the dryer in a
location where its door could conflict
with room doors.
,The appliance top is not
removable.
Carrying the dryer to the installation
site
aHandgrips under the cover overhang
for moving the appliance (arrows)
The rear cover overhang provides
handgrips for transport. To carry the
dryer from its shipping base to the
installation site, use the front feet of
the appliance and the rear top
overhang.
bPower cord
cRear venting connection
Washer-dryer stack
The dryer can be combined with a
Miele automatic washer in a
washer-dryer stack. For this, a "WTV
412" stacking unit* is required.
* Miele accessory available on order
,Installation of the stacking unit
may be performed only by an
authorized Miele technician.
31
Installation and connection
Leveling the dryer
,Ensure that is an air gap of at
least 10 mm between the underside
of the dryer and the floor. This air
gap must not be restricted by power
bars, high-nap carpets, etc.
Otherwise, sufficient air flow cannot
be guaranteed.
Ventilating the installation area
The air needed for drying is
extracted from the installation
space. You must therefore take
measures for sufficient room
ventilation, by opening windows for
instance.
To ensure trouble-free operation, the
dryer must be perfectly level.
Otherwise you can expect longer
running times and higher energy
consumption.
^ Compensate for floor irregularities by
turning the threaded feet in or out.
32
Installation and connection
Electrical connections
The dryer comes with a 5 ft long,
12/4 AWG cord and a NEMA 14-30 P
plug.
GROUNDING INSTRUCTIONS
This appliance must be grounded.
In the event of malfunction or
It should be connected to a
120/208-240 V, 30 A, 60 Hz AC power
supply. A 3 pole-4 wire grounding
power outlet (NEMA type 14-30 R) is
necessary.
breakdown, grounding will reduce
the risk of electric shock by
providing a path of least resistance
for electric current. This appliance is
equipped with a cord having an
equipment grounding conductor
and a grounding plug. The plug
must be plugged into an appropriate
outlet that is properly installed and
grounded in accordance with all
local codes and ordinances.
The dryer is equipped with a power
cable and plug ready for connection.
The plug must always be accessible to
facilitate disconnecting the dryer from
the electrical supply.
To eliminate a potential fire source, the
dryer should NEVER be connected by
means of extension cords, or by
WARNING – Improper connection of
the equipment grounding conductor
can result in a risk of electric shock.
Check with a qualified electrician or
service representative or personnel
if you are in doubt as to whether the
appliance is properly grounded.
multi-outlet power strips or the like.
The appliance data plate indicates the
nominal power consumption and the
approbiate fuse capacity. Please
compare the information on the data
plate with the electrical network data.
Do not modify the plug provided
with the appliance! If it will not fit the
outlet, have a proper outlet installed
by a qualified electrician.
33
Installing the dryer vent
General
Avoid:
– very long ducting systems.
– too many sharp bends or corners.
Important
The dryer should only be operated
when the moist air produced by
drying is ducted to the outside, by
means of: . .
Otherwise you will have less efficient
drying and increased time and energy
consumption.
. . . a flexible venting house, or
piping connected to the dryer, or
. . . a direct connection to a
through-wall pipe.
Use:
– for ventilation ducting:
rigid or flexible metal ducting with a
100 mm diameter.
– The appliance should not be
electrically connected while the
venting is being installed.
– for venting to the outside:
a wall pipe or window vent kit.
– The ducting outlet (for instance, a
wall pipe) is to be located so that the
moist air . .
Procedure
^ First measure the duct length
required. From this, calculate the
total duct length and determine the
required diameter (see the next
pages).
. . . cannot be drawn back into the
dryer installation space;
. . . will cause no structural damage
or unacceptable nuisance.
Note that a greater overall duct
length requires a larger pipe
diameter.
– Air required for drying is drawn from
the installation space.
Consequently, ensure that there is
sufficient room ventilation when
drying to prevent possible
asphyxiation from the possibility of
expelled gasses being drawn back
into the room, as well as to prevent
much longer drying times; for
example:
^ Then, decide which type of ducting
you wish to use (see "Installing
Venting Systems" in this section).
- Open windows;
- fitting unblockable air
inlets in the external wall;
- install window switches, so
that the dryer can only be
turned on when the window is
open.
34
Installing the dryer vent
Calculating total duct length
Table I
Each of bends and differing
Components
Comparative duct length
components of the dryer's venting
creates its own frictional resistance to
the flow of the exhaust air. This frictional
resistance is expressed in a
Flexible ducting
– 1 m laid straight
– 45° bend
1.8 m
1.5 m
(Bend radius = 0.25 m)
comparative duct length. The
– 90° bend
(Bend radius = 0.25 m)
2.5 m
comparative duct length indicates the
length of a smooth straight pipe (of the
same diameter), producing the same
resistance to air flow as the original
ducting component (Table I).
Vent hose(flexible or Alu-Flex)
– 1 m laid straight or 1 m straight
pipe
1.0 m
0.6 m
0.8 m
– 45° bend
(Bend radius = 0.25 m)
Adding together the comparative duct
lengths of all components reveals the
total duct length. The total duct length
is a calculated value that compares
how long a smooth straight venting
pipe would have to be for the same air
flow.
– 90° bend
(Bend radius = 0.25 m)
Wall vent kit or window vent kit
– with grill insert
3.8 m
1.5 m
– with non-return flap (hinged flap)
Non-return flap* for integration
into the vent ducting
14.3 m
(see section "dVent collector
duct")
Since an internal pipe diameter
Flat duct (for stacked
arrangement)
11.0 m
1.0 m
strongly affects flow's resistance, a vent
with a total duct length exceeding 20
m requires a larger diameter (Table II).
Left or right dryer vent opening
* Miele accessory available on order
Procedure
Table II
1. Measure the distance requiring
straight ducting. Multiply this value
by the corresponding comparative
pipe length from Table I.
Maximum permissible
total duct length
Diameter required
20 m
40 m
100 mm
125 mm
150 mm
2. Determine the number of bends and
components required. Add their
comparative lengths together using
Table I.
100 m
3. Add together all the comparative
lengths thus determined: Thus you
obtain the total duct length.
4. From Table II, determine which
internal duct diameter is required for
the total duct length.
35
Installing the dryer vent
Calculation example
Rear or side exhaust
connection
At the rear
Dryer is delivered with this connection
open.
^ Install the vent duct as described on
the following pages.
Sideways to left or right
A
Wall pipe, with grill insert
= 1 x 3.8 m Comparative duct
length
= 3.8 m
= 1.6 m
= 0.5 m
B/D 2 elbows, 90°
= 2 x 0.8 m Comparative duct
length
C
E
0.5 m plastic piping
= 0.5 x 1 m Comparative duct
length
Left side vent opening
= 1 m Comparative duct length = 1.0 m
Total duct length = 6.9 m
^ Unscrew the cover
(counterclockwise).
Result: Total duct length is less than 20
m (as per Table II). Therefore a pipe
diameter of 100 mm is adequate.
^ Refit the cover securely in the rear
vent outlet.
^ Install the vent duct as described on
the following pages.
36
Installing the dryer vent
Overview of vent systems
aFlexible metal duct hose
On this and the following pages you will
find descriptions of four venting
systems (a b c d) that can be
installed on the dryer.
Using the adapter provided, you can
easily install a vending duct house
(diameter 100 mm).
You require
– a duct hose (flexible or Alu-Flex).
– a wall pipe kit or a window vent kit.
^ Install the pipe (2) on the dryer using
an adapter (1).
Examples are shown on the next
page.
37
Installing the dryer vent
Examples:
Connection to exhaust flue
Window vent
1. Pipe with connector
2. Adapter for flexible vent hose
3. Exhaust flue, insulated against damp
1. Window vent kit (fitted in plexiglass
pane)
2. Adapter for flexible vent hose
,Ducting must not be connected
to a fireplace or gas flue that is in
use, nor to ducting which ventilates
rooms with fireplaces.
38
Installing the dryer vent
bDryer vent systems from
metal piping
Example
Smooth piping makes sense where
the vented air has to be carried a
considerable distance.
A pipe offers less resistance to the
discharge air than does, for instance,
a flexible ventilation duct. Time and
energy consumption improve with
smooth piping.
You require
– a connector adapter* (diameter 100
mm).
1. Wall vent kit
– a wall pipe kit or a window vent vent
kit.
2. Adapter
3. Metal dryer venting pipe,
diameter 4" (100 mm).
– Metal venting pipe from a builder or
plumbing supplier(diameter 100
mm). If a larger pipe diameter is
needed, adapters are necessary (for
example, to transition from 100 to
125 mm diameters).
* Miele accessory available on order
^ Install the pipe (2) in the dryer using
an adapter (1).
39
Installing the dryer vent
cConnecting directly to a wall Side view:
vent
If you can place the dryer directly
against the external wall of the room,
this vent configuration is
advantageous. The short overall pipe
length has a beneficial effect on time
and energy consumption. However,
you must make an opening in the wall
to install the wall kit.
You will need a wall pipe kit as well as a
flexible spacer ring.
ABefore breaking through the wall... . .
. . . read the installation instructions
accompanying the kit.
1. Wall pipe
2. Flexible foam gasket
. . . and study the following
dimensional drawings.
View from above:
BFit the flexible foam gasket (2) onto
the wall pipe adapter (1).
CPush the dryer up against the wall.
1. Wall pipe
2. Flexible foam gasket
40
Installing the dryer vent
dVent collector duct
To prevent condensed water buildup in
the non-operating dryers:
^ For each dryer, install a non-return
flap R directly on the collector duct.
You will need an optional Miele
accessory* (see right) for this.
When installing from 3 to a maximum
of 5 dryers, the pipe diameterD must
be enlarged.
Number Pipe diameter multiplication
of
factor from Table II
dryers
1 Connection to connection duct
2 Miele non-return flap*
1-2
3
1
3 additional Miele Adapter*
4 Vent hose, flexible
1,25
1,5
4 - 5
^ Press the non-return flap(2) fully into
the Adapter (3).
41
Installing the dryer vent
Washer-dryer stack
WTV 412 Stacking unit* without
worktop:
A = 94.2 cm
B = 170 cm
* Miele accessory available on order
42
Technical data
Height
850 mm
595 mm
634 mm
1,074 mm
Yes
Width
Depth
Depth with door open
Can be pushed under a worktop
– Height
850 mm
600 mm
Yes
– Width
Suitable for stacking
Weight
46 kg
Drum Volume
111 liters
2 m
Length of power cord
Voltage
Connected load (Watts)
Rated current (Amps)
Light bulb wattage
Test certifications granted
see data plate
43
Programmable functions
for changing
standard values
As needed, you can use
programmable functions to adapt
the dryer electronics to changing
requirements.
You can alter programmable
functions at any time.
44
Programmable functions
Extending the range of drying
levels
–
P and 0 flash alternatively in the
display (default setting).
The number appearing alternatively
You can extend the range of the
drying levels for many of the
programs:
with P means:
0 Default setting
Rotary iron+
I
Drying range steps added
(Express indicator light also flashes)
(dryer than Rotary Iron).
Hand iron+
DPressing the Start/Stop button
switches from one to the other.
(dryer than Hand iron).
Normal +
(dryer than Normal).
Additionally, the Extra dry level can
be selected for the Mixed and Denim
Jeans programs.
EUsing the I-On/0-Off button, switch
the dryer off.
The programming is now stored in
memory. You can change it again at
any time.
This programmable function is also
effective in the following programs:
Normal, Wrinkle free*, Mixed*,
Express, Denim/Jeans
To select the extended drying level:
^ Select a program.
(* no Rotary iron+).
^ Press the drying level button
repeatedly until one or two indicator
lights come on.
For programming and saving in the
memory, follow steps A to E.
The programmable function is
programmed using the buttons.
– Indicator lights Extra dry and Normal
= Normal+
Precondition:
– Indicator lights Normal and Hand
iron = Hand iron+
– The dryer is switched off.
– The door is closed.
– Indicator lights Hand iron and Rotary
iron = Rotary iron+
APress Start/Stop and keep it pressed
it during steps B-C.
BPress the I-On/0-Off button in.
Wait until the Start/Stop button lights up
continuously . . .
C. . . then release the Start/Stop
button.
– The Gentle indicator light flashes
twice briefly.
45
Programmable functions
Adjusting buzzer volume
The number appearing alternatingly
with P means:
The buzzer has two volumes.
0 Buzzer normal
(default setting)
For programming and saving in
memory, follow steps A to E.
I
Buzzer loud
(Express indicator light also flashes)
This function is programmed using the
buttons.
EPressing the Start/Stop button
switches from one number to the
other, and you simultaneously hear
the buzzer setting.
Precondition:
– The dryer is switched off.
– The door is closed.
FUsing the I-On/0-Off button, switch
the dryer off.
APress Start/Stop and keep it pressed
it during steps B-C.
The programming is now stored in
memory. You can change it again at
any time.
BPress the I-On/0-Off button in.
Wait until the Start/Stop button lights up
continuously . . .
C. . . then release the Start/Stop
button.
DPress the Gentle button once.
– The Gentle indicator light flashes
briefly four times.
–
P and 0 flash alternatingly in the
display (default setting).
46
Programmable functions
Set memory function
The number appearing alternatingly
with P means:
The electronics memorizes any
selected program with extra options.
The duration of a Smoothing program
will also be stored in memory.
I
Memory
(Express indicator light also flashes)
0 no Memory
These settings will be used for the
next drying. They can be accepted,
or changed by using the buttons.
(default setting)
EPressing the Start/Stop button
switches from one to the other.
For programming and saving in
FUsing the I-On/0-Off button, switch
the dryer off.
memory, follow steps A to E.
The programmable function is
programmed using the buttons.
The programming is now stored in
memory. You can change it again at
any time.
Precondition:
– The dryer is switched off.
– The door is closed.
APress Start/Stop and keep it pressed
it during steps B-C.
BPress the I-On/0-Off button in.
Wait until the Start/Stop button lights up
continuously . . .
C. . . then release the Start/Stop
button.
DPress the Gentle button twice.
– The Gentle indicator light flashes
briefly six times.
–
P and 0 flash alternatingly in the
display (default setting).
47
Programmable functions
Extending cooldown time
The number appearing alternatingly
with P means:
You can individually lengthen the
cooldown phase the occurs before
the end of a program. Fabrics will be
more completely cooled down.
0 Default setting
I
Five minutes longer cooldown time
(Express indicator light will flash
once)
Cooldown time
2 Ten minutes longer cooldown time
(Express indicator light will also flash
twice)
– can be extended by two stages.
– it does not function for Smoothing
programme.
EPressing the Start/Stop button
switches from one to the other.
For programming and saving in
memory, follow steps A to E.
FUsing the I-On/0-Off button, switch
the dryer off.
The programmable function is
programmed using the buttons.
The programming is now stored in
memory. You can change it again at
any time.
Precondition:
– The dryer is switched off.
– The door is closed.
APress Start/Stop and keep it pressed
it during steps B-C.
BPress the I-On/0-Off button in.
Wait until the Start/Stop button lights up
continuously . . .
C. . . then release the Start/Stop
button.
DPress the Gentle button three times.
– The Gentle indicator light flashes
briefly seven times.
–
P and 0 flash alternatingly in the
display (default setting).
48
Programmable functions
Change function of Filter/Vent
indication
The number appearing alternatingly
with P means:
0 The Filter/Vent indicator is
Lint should be removed after drying.
At the same time, the Filter/Vent
indicator light reminds you to do so
as soon as a certain degree of lint
has accumulated. You can yourself
decide which degree of lint
accumulation will trigger that
reminder.
deactivated
I
The Filter/Vent indicator comes on
only when there is a heavy lint
buildup
(Express control light additionally
flashes once)
2 default setting
(the Express indicator light also
flashes twice)
Determine by trial and error which of
the four options responds to your
drying practices.
3 The Filter/Vent indicator will come
on when there is only a light lint
buildup
For programming and saving in
memory, follow steps A to E.
(The Express indicator light also
flashes three times)
The programmable function is
programmed using the buttons.
EPressing the Start/Stop button
switches from one to the other.
Precondition:
– The dryer is switched off.
– The door is closed.
FUsing the I-On/0-Off button, switch
the dryer off.
The programming is now stored in
memory. You can change it again at
any time.
APress Start/Stop and keep it pressed
it during steps B-C.
BPress the I-On/0-Off button in.
Wait until the Start/Stop button lights up
continuously . . .
C. . . then release the Start/Stop
button.
DPress the Gentle button four times.
–
The Gentle indicator light flashes
once slowly.
–
P and 2 flash alternatingly in the
display (default setting).
49
Programmable functions
Adjust keypad tone
The number appearing alternatingly
with P means:
An audible tone sounds every time a
button is pressed.
0 no Keypad tone
(default setting)
For programming and saving in
I
Keypad tone on
(Express indicator light also flashes)
memory, follow steps A to E.
The programmable function is
programmed using the buttons.
EPressing the Start/Stop button
switches from one to the other.
Precondition:
FUsing the I-On/0-Off button, switch
the dryer off.
– The dryer is switched off.
– The door is closed.
The programming is now stored in
memory. You can change it again at
any time.
APress Start/Stop and keep it pressed
it during steps B-C.
BPress the I-On/0-Off button in.
Wait until the Start/Stop button lights up
continuously . . .
C. . . then release the Start/Stop
button.
DPress the Gentle button five times.
– The Gentle indicator light flashes
once slowly and once briefly.
–
P and 0 flash alternatingly in the
display (default setting).
50
Programmable functions
Changing water conductivity
setting
DPress the Gentle button six times.
– The Gentle indicator light flashes
once slowly and twice briefly.
,This programmable function
should be adjusted only when
residual water content is erroneously
determined owing to the extreme
softness of the water.
–
P and 0 flash alternatingly in the
display (default setting).
The number appearing alternatingly
with P means:
0 Default setting
Important condition
I
Lower conductivity setting
(Express indicator light also flashes)
The water in which fabrics are washed
may be extremely soft with a
conductivity value less than 150 μS/cm.
Drinking water conductivity can be
ascertained from your local water
supplier.
EPressing the Start/Stop button
switches from one to the other.
FUsing the I-On/0-Off button, switch
the dryer off.
Activate this programmable function
only if the above-mentioned
condition applies.
The programming is now stored in
memory. You can change it again at
any time.
Otherwise the drying result will be
unsatisfactory.
For programming and saving in
memory, follow steps A to E.
The function is programmed using the
buttons.
Precondition:
– The dryer is switched off.
– The door is closed.
APress Start/Stop and keep it pressed
it during steps B-C.
BPress the I-On/0-Off button in.
Wait until the Start/Stop button lights up
continuously . . .
C. . . then release the Start/Stop
button.
51
Alteration rights reserved/ 2009
M.-Nr. 07 323 240 / 01
|